How To Add the Lubricator to the TOUGH GUN TT3 Reamer

WARNING: Ensure the power and air supplies to the TOUGH GUN® Reamer are disconnected or disabled prior to working with the Reamer.  ItemDescriptionPart NumberQty15/16″ x 1/18″ NPT QCTR-223122Bulkhead AdaptorLR-500-5123SpacerLR-500-50-514M6x1x20mm LG SHCS – Black OxideF1-M6X1-20B25Steel Line Kit – For LubricatorLR-500-5016Lubricator TT-LUB-SMC1 1. Remove lubricator kit from the box and inspect for any damage. 2. Remove the reservoir […]

read more...

How To Install the QUICK LOAD Liner in the AutoLength System

Remove consumables (nozzle, contact tip and retaining head). Pull existing QUICK LOAD® Liner from the neck using pliers.Remove the protective cap from the new QUICK LOAD Liner.Insert the new QUICK LOAD Liner through the neck. Push the liner in using short strokes to prevent the liner from kinking.   Feed the liner into the torch until […]

read more...

How To Install the AutoLength Pin

IMPORTANT NOTICE: The AutoLength™ Pin is one component of the QUICK LOAD® Liner AutoLength System. This pin is designed specifically for use with QUICK LOAD Liners from Tregaskiss. Do not attempt to use with any other type of liner. AutoLength Pins look the same as standard power pins, but can only be used with QUICK LOAD […]

read more...

How To Upgrade from Conventional Liners to QUICK LOAD Liners

Replace Your Liner in Less Than 1/2 the Time with the QUICK LOAD® Liner from Tregaskiss! To convert to the QUICK LOAD Liner, update your conventional liner part number as per the chart below. QUICK LOAD Liner Conversion Chart Wire SizeQUICK LOAD LinerReplaces Conventional LinerDescriptionLengthI.D.0.023″415-23-15Q415-23-15High Carbon Steel – Round Wound16.5′0.050″0.030″415-30-6Q415-30-6High Carbon Steel – Round Wound7.5′0.062″0.030″415-30-15Q415-30-15High […]

read more...

How To Remove and Install Wire Brake in a TOUGH GUN ThruArm Series MIG Gun

NOTICE: This product is factory set for wire equal to or smaller than 0.045“. If you are using wire 0.052” and larger, please remove the wire guide within the neck housing and replace it with the larger size (part #598-116) that is supplied in the box with this product. Removal and Installation Instructions Follow the […]

read more...

How To Convert from Single Taper Retaining Heads to TOUGH LOCK Retaining Heads Featuring Dual Taper Technology

TOUGH LOCK® retaining heads featuring dual taper technology have a second taper at the rear of the retaining head where it connects with the neck. This dual taper design: Locks your gun from contact tip to neckIncreases electrical conductivityHelps keep  your consumables running coolerDecreases costly downtime To enjoy the benefits of TOUGH LOCK retaining heads at no […]

read more...

How To Install Air Blast on TOUGH GUN G1 Series Robotic MIG Guns

AIR BLAST KIT 508-A (does not include housing)  Remove 408-200-9A using a standard screwdriver Remove 408-200-8A using a standard screwdriver Thread 410-45-2 into 408-200-8A using xx wrench Insert TR-2237 into push-lock connections of TR-2232 and 410-45-2. Insert TR-2232 into air supply, 60-80 psi air pressure 408-200-9A 408-200-8A (internal threads) 410-45-2

read more...

How To Mount the RS-500 Sprayer as a Stand-Alone Unit

The sprayer should be installed within the weld cell at a convenient location. Be sure to consider movable fixtures and the confines of the robot. Each sprayer comes complete with all required installation hardware and mounting brackets.

read more...

How To Mount the SR-500 Sprayer to the TOUGH GUN Reamer

The TOUGH GUN­® Reamer has all the necessary mounting holes for installation of the SR-500 spray unit. Remove the plug from the side of the frame detail and replace with the supplied bulkhead fitting.Attach the spray head bracket to the TOUGH GUN Reamer using the two (2) screws provided.Attach the spray head to the TOUGH […]

read more...

How To Install the TOUGH GUN Wire Cutter to the TOUGH GUN Reamer

WARNING: Ensure the power supply is off and disconnected before proceeding! Mounting the Wire Cutter The Wire Cutter should be installed within the weld cell. The base plate has been designed for mounting on top of the TOUGH GUN™ Reamer. Be sure to consider movable fixtures and the confines of the robot. Attach the Wire Cutter […]

read more...

How To Install the TOUGH GARD Multi-Feed System to the TOUGH GUN Reamer

Step 1: It is best to start by establishing the pail/drum location. This way it will be easier to run the lines and permanently secure them.Start by removing the reservoir from the spray unit.NOTE: Shut the vent cap (if applicable) and turn the reservoir upside down when it comes off the spray unit to avoid […]

read more...

How To Install the TOUGH GUN Reamer TT Series

WARNING: Ensure the power supply is off and disconnected before proceeding! Mounting the TOUGH GUN® Reamer The TOUGH GUN Reamer should be installed within the weld cell at a convenient location. Be sure to consider movable fixtures and the working envelope of the robot.Affix the TOUGH GUN Reamer base to a sturdy platform using the four […]

read more...

How To Install a Power Pin to a Tregaskiss MIG Gun

Thread the power pin into the rear housing.Tighten the power pin into the rear housing using a 1-inch (2.54 cm) wrench on the rear housing and a 3/4-inch (19 mm) wrench on the power pin. Torque to 18 ft.-lbs. (24.4Nm).IMPORTANT: The thread-in two-piece power pin has a taper to seat and lock the power pin […]

read more...