Video | QUICK LOAD Liner AutoLength Introduction

QUICK LOAD™ Liner AutoLength™ Introduction Please accept preferences, statistics, marketing cookies to watch this video. Learn about the innovative QUICK LOAD Liner AutoLength from Tregaskiss. QUICK LOAD liner installs through the front of the MIG gun in less than half the time required to install a conventional liner. Increases production uptime, provides cost savings and […]

read more...

How To Install the TOUGH GUN Reamer Stand

How To Install the TOUGH GUN Reamer Stand Unpack the TOUGH GUN® reamer stand and inspect for any damage ensuring that there are no bent, corroded, or missing parts.  Confirm that the stand has been manufactured to the correct height. The stand can be ordered in any of the heights shown in the table below: […]

read more...

How To Install an LSR+ Unicable Extension

How To Install an LSR+ Unicable Extension   Important Note: If you find that your cable is too short and the power pin won’t plug into the feeder, please use the 1″ cable extension.  Thread the 414-700EX-01 cable extension into the brass block of the LSR+ Unicable and torque to 18 ft.-lbs. Thread power pin clockwise […]

read more...

How To Install the LSR+ Flange on an OTC Daihen Robot

How To Install the LSR+ Flange on an OTC Daihen Robot  Note: The following instructions are applicable for OTC Daihen® robot models NB4, NB4L, FD-B4 and FD-B4L  Slide one half of the clamp between LSR+ Unicable and robot wrist. Make sure LSR+ clutch cable slot is facing up. Take second half of the clamp and […]

read more...

How To Install a TOUGH GUN ThruArm Robotic MIG Gun onto a Motoman Robot

How To Install a TOUGH GUN ThruArm Robotic MIG Gun onto a Motoman Robot Note: The following installation instructions are applicable to installing TOUGH GUN® TA3 robotic air-cooled MIG guns on Motoman® MA1440, MA2010 and MA3120 robots  Step 1: Aluminum Spacer Installation Step 2: LSR+ Unicable Installation into Connector Step 3: Connector, Outer Cover, Power […]

read more...

How To Install a TOUGH GUN TA3 MIG Gun on a Panasonic Robot

How To Install a TOUGH GUN TA3 MIG Gun on a Panasonic Robot Important Note: The following instructions are applicable for installing TOUGH GUN® TA3 robotic air-cooled MIG guns on Panasonic® TM-1100, TM-1400, TM-1600 and TM-1800 Robots Step 1: Transition Flange and Spacer Installation Step 2: LSR Unicable Installation into Connector Step 3: Connector Installation  […]

read more...

How To Install an LSR+ Flange on an ABB Robot

How To Install an LSR+ Flange on an ABB Robot Note: The following instructions are applicable for ABB® IRB1600ID, IRB1520ID, IRB2600ID and IRB1660ID robot models  Secure the LSR+ Flange on the robot wrist with M6x1.0-25mm LG SHCS. Slide the LSR+ Unicable through the robot wrist and LSR+ Flange. Install the LSR+ Unicable on the TOUGH […]

read more...

How To Install or Replace the PER-2599 Motor

How To Install or Replace the PER-2599 Motor The following images detail the installation of new motor PER-2510. This motor is not compatible with the existing mounting bracket on spatter cleaner untis made before March 2012 and may also require new valve assembly ER-2700, series number ER-1635 and lower. The new motor is assembled and […]

read more...

How to Replace QUICK LOAD Liners Into Retainer or AutoLength Pin

How to Replace QUICK LOAD Liners into Retainer or AutoLength Pin 1. Remove consumables (nozzle, contact tip and retaining head). 2. Pull the existing QUICK LOAD™ Liner from the neck using pliers. 3. Remove the protective cap from the new QUICK LOAD Liner. 4. Insert the QUICK LOAD Liner through the neck using the wire […]

read more...

How to Install QUICK LOAD Liners When Replacing Conventional Liners

How to Install QUICK LOAD Liners When Replacing Conventional Liners 1. Remove the protective cap from the new QUICK LOAD® Liner. 2. Install this liner from the back of the MIG gun with retainer attached (using the same procedure as installing a conventional liner). Future replacements will be done from the front. (Refer to How […]

read more...

How To Install the TT3-500 TOUGH GUN Sprayer onto a TOUGH GUN TT3 Reamer

How To Install the TT3-500 TOUGH GUN Sprayer onto the TOUGH GUN TT3 Reamer The following images and instructions detail the installation of the TT3-500 TOUGH GUN® Sprayer onto the TOUGH GUN TT3 Reamer. Open the box and inspect the items for any noticeable damage to the parts during shipping. The TT3-500 Sprayer should only […]

read more...

How To Install the Filter-Regulator Unit to the TOUGH GUN TT3 Reamer

How To Install the Filter/Regulator Unit to the TOUGH GUN TT3 Reamer The following images and instructions detail the installation of the Filter/Regulator unit onto a TOUGH GUN® TT3 reamer: Remove the Filter/Regulator from the box. Ensure that all the required parts are present (see Figure 1): Filter Body Regulator Pressure Gauge Mounting Bracket Safety […]

read more...