Remove nozzle, contact tip, and gas diffuser / retaining head and lay cable straight. Using a 10 mm wrench, turn liner lock counterclockwise until it is free from the power pin. Remove liner from gun assembly. Remove the screw and assembly from rear strain relief and slide rear strain relief back over power pin. Position control [...]
Remove liner from gun assembly. Viewing quick disconnect from cable end, align wave spring and large snap ring with opening access slot. Compress large snap ring with internal snap ring pliers and remove locking sleeve. Remove small external snap ring with external snap ring pliers from power pin. Remove the control leads from the rigid strain [...]
Remove liner and strain relief from the gun assembly. Disconnect the Euro block leads from the gun by cutting as close as possible on both sides of the butt connectors in order to preserve wire for later retermination. Slide adaptor nut toward cable, thus exposing the Euro block. Remove Euro block from end fitting using wrenches [...]
Remove consumables (Nozzle, Retaining Head, Contact Tip).Remove the liner from the gun.Mount neck in the vise.Disassemble handle and remove switch from leads.Move the handle back. Bend cable behind connector cone. Cut cable at bend.Slide two large “Oetiker” clamps 1.5 ft. down the cable (required for crimping later).From your cut (end of cable), measure 3” back [...]
1. Remove consumables (nozzle, contact tip and retaining head). 2. Pull the existing QUICK LOAD™ Liner from the neck using pliers. 3. Remove the protective cap from the new QUICK LOAD Liner. 4. Insert the QUICK LOAD Liner through the neck using the wire as a guide. Push the QUICK LOAD Liner in using short [...]
Important Note: This product is factory set for wire equal to or smaller than 0.045”. If you are using wire 0.052” and larger, please remove and replace the wire guide within the neck housing and replace it with the larger size (part #598G2-116) that is supplied in the product box. Wire Brake Kit ItemPart NumberDescription1599Pushing [...]
Remove the neck, consumables and conduit from torch.Slide the torch through robot wrist and conduit.Secure the torch on robot wrist.Secure the conduit with two clamps and M5 SHCS.Connect the torch to the feeder.Install the neck, liner and consumables. INS072 11/2010
The following images detail the installation of new motor PER-2510. This motor is not compatible with the existing mounting bracket on spatter cleaner untis made before March 2012 and may also require new valve assembly ER-2700, series number ER-1635 and lower. The new motor is assembled and marked inside the new mounting bracket for reference [...]
Step 1: Remove the 2 screws which retain Item #1 and slide cover back to expose Item #2.Locate Items #2 and #3 and remove both pieces. Once Items #2 and #3 have been removed, remove Item #4 from the front housing by loosening the pinch bolt through clearance hole in aluminum spacer. Step 2: Install Items [...]
Important Note: The following instructions are applicable for installing TOUGH GUN® TA3 robotic air-cooled MIG guns on Panasonic® TM-1100, TM-1400, TM-1600 and TM-1800 Robots Step 1: Transition Flange and Spacer Installation Step 2: LSR Unicable Installation into Connector Step 3: Connector Installation INS096 11/16
Wire Brake Tool #450-17 Instructions Remove the neck and consumables (not shown in the diagram).Remove (unthread) the Wire Brake Pushing Unit.Using the Wire Brake Tool, slide the Wire Guide Holder out of the connector cone assembly.Clean any debris or residue on the Wire Guide Holder. To Reassemble the Wire Guide Holder Using the Wire Brake [...]
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to install a rotatable neck jump liner on a BTB Semi-Automatic MIG Gun
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to replace a rotatable neck on a BTB Semi-Automatic MIG Guns
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to replace the switch on a T Series BTB Semi-Automatic MIG Gun
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to repair a unicable on a Bernard BTB Semi-Automatic MIG Gun
Please accept preferences, statistics, marketing cookies to watch this video. Learn about the innovative QUICK LOAD Liner AutoLength from Tregaskiss. QUICK LOAD liner installs through the front of the MIG gun in less than half the time required to install a conventional liner. Increases production uptime, provides cost savings and ensures operator safety.
Please accept preferences, statistics, marketing cookies to watch this video. Watch this demonstration to learn how to safely and properly remove the motor and replace the belt in the TOUGH GUN TT3 Reamer.
Please accept preferences, statistics, marketing cookies to watch this video. Check out this quick demonstration to learn how to replace the clamp limit switch in the TOUGH GUN TT3 Reamer.
Please accept preferences, statistics, marketing cookies to watch this video. Watch this demonstration to learn how to replace the upper and lower limit switches for the spindle in the TOUGH GUN TT3 Reamer.
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to replace a dual shunt cable (5800) on a TOUGH GUN TA3 Robotic Air-Cooled MIG Gun.
Please accept preferences, statistics, marketing cookies to watch this video. Learn how to replace the LSR Unicable on a TOUGH GUN TA3 robotic air-cooled MIG gun
Please accept preferences, statistics, marketing cookies to watch this video. Find out how easy it is to replace the circuit board with its smart-keyed connections in the TOUGH GUN TT3 Reamer.
Please accept preferences, statistics, marketing cookies to watch this video. Check out this helpful video to learn more about how to install your TOUGH GUN TT3 Reamer.
Step 1: It is best to start by establishing the pail/drum location. This way it will be easier to run the lines and permanently secure them.Start by removing the reservoir from the spray unit.NOTE: Shut the vent cap (if applicable) and turn the reservoir upside down when it comes off the spray unit to avoid [...]